Field Notes 15 November 2026 long range
Your Sight Tape Was Printed for Somebody Else's Sight
Here's a confession. For a while, The Forge printed sight tapes for the Black Gold MODD that were 42% short. Every one of them.
Nobody emailed me about it. That's the part that bugs me. Somebody out there probably printed one, stuck it on, shot 20 dead on because that's where they zeroed, then walked back to 60 and watched arrows land nowhere near the dot. And they blamed themselves. Or their release. Or the wind.
It was the tape.
A tape is a ruler for one specific sight
This is the thing most guys don't get about slider tapes. The tape doesn't care about yards. It cares about how far the scope housing physically moves for every inch of drop your arrow picks up downrange. And that number changes from sight to sight.
Think of it like gearing. On a plain vertical slider, the scope moves straight up and down and the scale reads that movement one-to-one. On a dial or wheel sight, you turn a knob and the housing moves some fraction of that. Same arrow, same speed, same peep height, but the marks on the tape have to be spread out or squeezed together to match how that particular sight translates rotation into movement.
So every sight has a ratio. Call the UV Slider 2 a 1.0. The HHA Tetra family runs at 2.23. The MODD is 1.727. The Spot Hogg Fast Eddie is 1.53 while the Hogg Father is 1.677, which means two sights from the same company, sitting next to each other on the shelf, need different tapes. Some sights even run backwards, with the long-range marks at the bottom of the scale instead of the top.
Get the ratio wrong and your tape is a perfectly good ruler for a sight you don't own.
How small errors hide
The MODD mistake was a big one, and big mistakes are almost easy. You'd catch 42% at 40 yards.
The sneaky ones are small. I had the Tetra family at 2.18 instead of 2.23. That's about two percent. On my own Elite Omnia with a Tetra Max RYZ X3, that put my 100-yard mark at 2.828 inches from zero when it should've been 2.893. Sixty-five thousandths of an inch. Sounds like nothing.
It's more than three pin-widths on a .019 pin.
And here's why that's dangerous. A two percent tape error doesn't show up at 20. It barely shows up at 40. Most hunters sight in at 20, check 40, maybe poke at 60 once, and call it good. The error grows with distance, so the exact shots where you need the tape to be honest are the ones you've practiced least. Late season elk across a basin. A mule deer bedded at 70. That's where it bites.
I see this all the time at the range. Guy prints a tape off a generic chart, picks the closest sight name in the dropdown, and figures "close enough." Then he spends a whole afternoon re-printing tapes, swapping speeds, convinced his chrono is lying. His chrono's fine. He picked the wrong gear.
What I changed
I quit trusting my own numbers. Every sight ratio in The Forge got checked against an independent ballistics solver, with the arrow, speed, peep height and sight radius held dead constant and only the sight swapped out. When you do it that way, the ratio between two sights comes out as one fixed number at every distance. Pure gearing. Which is exactly how it should behave if the model's right.
Thirty-some sights moved. The MODD went from 1.00 to 1.727. The Tetra family went to 2.23. Fast Eddie and the Boonie came off the Hogg Father number. A pile of TruGlo, Trophy Ridge, CBE, Copper John and Sure-Loc sights got flagged as inverted, meaning the scale runs the opposite direction from what you'd assume. Every one of those is now locked in with a test so it can't quietly drift back.
Then I ran three different setups out to 120 yards across nine sights. Ratios held at every range. The leftover error is tiny and it's in the arrow flight model, not the sight. Worst case I found was about four-tenths of a yard long at 120. I can live with that. You can too.
Check yours before you trust it
If you shoot a slider or a dial and you've never confirmed your tape at the long end, do this before your next hunt. Not next year. This week.
Shoot your 20 and confirm it's dead on. Then skip 30 and 40 entirely and go straight to the longest distance you'd honestly take a shot at, plus ten. Shoot five arrows with the dial set where the tape says. If the group is centered, your tape is good. If it's high or low, don't move the tape. Write down how far off you are, then check one more distance in the middle. If the error grows steadily with range, your ratio is wrong or your sight's set up as the wrong model. If it jumps around, that's you, and that's a different post.
And if your sight isn't on the list, tell me. I'd rather add one than have you guess.
Go rebuild your tape in the sight tape builder in The Forge. Pick your exact sight model, not the closest one, punch in your real chrono numbers, and print it. Then go shoot the long end and prove it to yourself. A tape you've confirmed at 70 is worth more than any tape you trust because a computer printed it. Mine included.